ATMEGA328P-PU Microchip AVR Microcontroller DIP-28

ATMEGA328P-PU Microchip AVR Microcontroller 8bit 20MHz 32 kB Flash DIP-28

The ATmega48A/PA/88A/PA/168A/PA/328/P is a low power, CMOS 8-bit microcontrollers based on the AVR enhanced RISC architecture. By executing instructions in a single clock cycle, the devices achieve CPU throughput approaching one million instructions per second (MIPS) per megahertz, allowing the system designer to optimize power consumption versus processing speed.

Features:

• High Performance, Low Power AVR 8-Bit Microcontroller Family
• Advanced RISC Architecture
  • 131 Powerful Instructions – Most Single Clock Cycle Execution
  • 32 x 8 General Purpose Working Registers
  • Up to 20 MIPS Throughput at 20MHz
• On-chip 2-cycle Multiplier
• High Endurance Non-volatile Memory Segments
  • 4/8/16/32KBytes of In-System Self-Programmable Flash program memory
  • 256/512/512/1KBytes EEPROM
  • 512/1K/1K/2KBytes Internal SRAM
  • Write/Erase Cycles: 10,000 Flash/100,000 EEPROM
  • Data retention: 20 years at 85°C/100 years at 25°C(1)
  • Optional Boot Code Section with Independent Lock Bits
    • In-System Programming by On-chip Boot Program
    • True Read-While-Write Operation
  • Programming Lock for Software Security
• QTouch® library support
  • Capacitive touch buttons, sliders and wheels
  • QTouch and QMatrix™ acquisition
  • Up to 64 sense channels
• Peripheral Features
  • Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode
  • One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode
  • Real Time Counter with Separate Oscillator
  • Six PWM Channels
  • 8-channel 10-bit ADC in TQFP and QFN/MLF package
    • Temperature Measurement
• Channel 10-bit ADC in PDIP Package
  • • Temperature Measurement
  • Programmable Serial USART
  • Master/Slave SPI Serial Interface
  • Byte-oriented 2-wire Serial Interface (Philips I2C compatible)
  • Programmable Watchdog Timer with Separate On-chip Oscillator
  • On-chip Analog Comparator
  • Interrupt and Wake-up on Pin Change
• Special Microcontroller Features
  • Power-on Reset and Programmable Brown-out Detection
  • Internal Calibrated Oscillator
  • External and Internal Interrupt Sources
  • Six Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby, and Extended Standby
• I/O and Packages
  • 23 Programmable I/O Lines
  • 28-pin PDIP, 32-lead TQFP, 28-pad QFN/MLF and 32-pad QFN/MLF
• Operating Voltage: 1.8 – 5.5V
• Temperature Range: -40°C to 85°C
• Speed Grade: 0 – 4MHz@1.8 – 5.5V, 0 – 10MHz@2.7 – 5.5.V, 0 – 20MHz @ 4.5 – 5.5V
• Power Consumption at 1MHz 1.8V, 25°C
  • Active Mode: 0.2mA
  • Power-down Mode: 0.1µA
  • Power-save Mode: 0.75µA (Including 32kHz RTC)

Pin  Configuration:

Specifications:

Applications:

• Arduino Development.
• Embedded Systems & IoT.
• Robotics & Automation.
• Data Logging & Monitoring.
• Wearable & Low-Power Applications.
• Consumer Electronics.
• Custom DIY Projects.

Datasheet:

ATMEGA328P-PU Microcontroller